U.S. Dealer Representative/Support

Building Automation

Vector DDC controllers run the rooftop units, unit heaters and radiant floor zones in light-commercial and high-end residential buildings, and talk BACnet or Modbus to whatever system is already there. No gateways, no lock-in, no per-point licensing. Supported across the U.S. from the Twin Cities.

Cutaway of a small office and shop building on a winter night. A Vector controller in the mechanical room is wired to an outdoor sensor, a room sensor in the office, the rooftop unit, a wall-hung boiler, a unit heater hanging in the shop, and heating panels under the shop floor. The office computer runs the building management system, and a phone checks in remotely.
Who we are

An engineer's controls partner, not a sales pitch.

Premier Energy Controls is the U.S. Dealer Representative/Support for Vector Controls, bringing BTL-certified, open-protocol building automation hardware to contractors, integrators, owners, and specifying engineers across light-commercial and high-end residential projects.

We work the gap that most product lines miss: jobs that have outgrown a residential thermostat but don't need (or can't justify the cost of) a full building management system. Zero licensing, and a controller that drops straight into whatever head-end a building already runs.

No proprietary sensors. No per-point fees. No vendor lock-in disguised as a feature.

Equipment It Controls

Vector controllers run the equipment on most light-commercial and high-end residential jobs, including:

  • BoilersStaging and outdoor reset
  • Heat PumpsAir-source and geothermal
  • Rooftop Units (RTUs)Heating, cooling, economizer
  • FurnacesStaged or modulating
  • Air HandlersSupply and mixed air
  • Fan Coil Units2-pipe and 4-pipe
  • ChillersEnable and setpoint reset
  • ERVs and HRVsCO₂-based ventilation
  • Humidity ControlHumidifiers and dehumidifiers
  • Radiant Floor ZonesZone valves and pumps
  • Make-Up Air UnitsInterlocked with exhaust
  • Unit HeatersGarages, shops, warehouses
Featured controller

The TCX2-40863, up close.

A panel-mount, quad-loop programmable controller built on the X2 operating system, sized for real light-commercial jobs, priced to make sense for them too.

Vector Controls TCX2-40863 controller on a counter in front of shelves of Vector boxes
Vector Controls · X2 Series

TCX2-40863 Programmable Controller

Four control loops, universal I/O, and a built-in RS-485 interface for peer-to-peer terminals, all commissioned free of charge through EasySet, on the bench or in the field.

  • 6 relay outputs
  • 8 hardwired inputs
  • 3 analog outputs, 0–10V
  • Onboard humidity sensing
  • Controls up to 4 pieces of equipment
  • BTL Certified
  • BACnet MS/TP · IP
  • Modbus RTU · TCP
  • No licensing fees

The rest of the controller family

Photos courtesy of Vector Controls
Vector Controls TRI2 wall-mount controller and sensor
Wall Mount · X2

TRI2

Dual-loop controller and room sensor with built-in temperature and humidity; fits a standard US electrical box.

Vector Controls TCI2 compact panel-mount controller
Compact Panel Mount · X2

TCI2

Small dual-loop controller: 4 universal inputs, 2 relays and 2 analog outputs, with BACnet/Modbus over RS-485, Wi-Fi or Ethernet.

Vector Controls TCI-W22 V2.0 wall-mount universal controller
Wall Mount · Configurable

TCI-W22 V2.0

Dual-loop wall-mount PI controller with 2 inputs, 2 relays, 1 analog output, 7-day schedules and a backed-up clock.

Why open protocol

Vector's X2 platform was built so nothing you install today becomes a dead end tomorrow, for the building or for your budget.

Comms

BACnet + Modbus, native

MS/TP and RTU over RS-485; BACnet/IP and Modbus TCP over Ethernet or Wi-Fi. No gateway, no translator.

Certification

BTL certified & listed

Certificates 30869 (MS/TP) and 30963 (IP), verifiable on the BACnet International registry.

Licensing

Free, permanently

EasySet for configuration, EasyX2 for remote monitoring: every app and firmware update, no cost.

Integration

Drops into any BMS

Niagara, Metasys, Distech, or its own built-in web interface if there's no head-end at all.

One platform, a full product line.

Every device below runs the same free X2 operating system and the same open protocols: controllers, sensors, and transmitters that all drop into the same BACnet or Modbus network.

Vector Controls SRD2 wall-mount controller and sensor
Wall-Mount Controller

SRD2 Series

Room controller and sensor measuring temperature, humidity, CO₂, VOC, and particles.

Vector Controls configurable fan coil controller
Configurable Controls

TRA-F Fan Coil Series

Communicating fan coil controllers with Modbus output for zone-level terminal units.

Vector Controls SRC-C CO2 and temperature monitor
Smart Transmitter

SRC-C CO₂ Monitor

Desktop or wall-mount CO₂ and temperature monitor for indoor air quality monitoring and demand-controlled ventilation.

Vector Controls passive temperature sensors
Passive Sensors

Temperature Sensor Line

Flying-lead, surface-mount, and duct-mount NTC temperature sensors that pair with any X2 Series controller.

Full specifications, datasheets, and installation PDFs for every product are available directly from the manufacturer at vectorcontrols.com.

Where it fits

Built for the jobs in between.

Too much building for a thermostat. Too small a job to justify a licensed BMS deployment. This is exactly that middle ground.

Light-commercial retrofits

Offices, restaurants, churches, multi-family, and schools trading pneumatic or dumb thermostats for real DDC.

High-end residential

Integrates alongside Control4, Crestron, and Savant for whole-home comfort and ventilation control.

Zone additions to an existing BMS

Add equipment to a Niagara or Metasys site without expanding your licensed point count.

Furnace / humidifier / ERV coordination

True staged or modulating equipment sequencing across all three systems from one controller.

Standalone DDC replacement

Aging pneumatic or unitary controls upgraded with a built-in browser interface, no head-end required.

OEM & panel-builder integration

Vector's OEM program supports private-label configurations for equipment manufacturers.

BACnet, Modbus and DDC, answered.

Can BACnet and Modbus work together without a gateway?

With Vector X2 controllers, yes. Each controller can speak BACnet MS/TP or Modbus RTU over RS-485, and BACnet/IP and Modbus TCP over Ethernet or Wi-Fi, natively. Because both protocols are built in, there is no separate gateway or protocol translator to buy, configure or maintain, and the controller drops into whichever network the building already runs.

What are the two types of Modbus?

Modbus RTU and Modbus TCP. Modbus RTU runs over a serial RS-485 connection, while Modbus TCP runs over an IP network such as Ethernet or Wi-Fi. Vector X2 controllers support both natively, alongside BACnet MS/TP and BACnet/IP, so the same controller works on older serial networks and newer IP networks.

Is BACnet/IP the same as Ethernet?

Not quite. Ethernet is the physical network, while BACnet/IP is the BACnet protocol carried over an IP network, which can run on Ethernet or Wi-Fi. BACnet MS/TP is the serial version that runs over RS-485 wiring. Vector X2 controllers support both BACnet/IP and BACnet MS/TP, so one product line covers both kinds of installation.

What is the difference between DDC and a BMS?

DDC (direct digital control) is the controller that reads sensors and runs the HVAC equipment. A BMS, or building management system, is the supervisory layer that monitors many controllers from one place. Vector X2 controllers are DDC controllers that can run on their own with a built-in web interface, or drop into a Niagara, Metasys or Distech BMS.

Can pneumatic controls be converted to DDC?

Yes. Replacing aging pneumatic or unitary controls with DDC is one of the most common jobs for Vector controllers. Offices, restaurants, churches, multi-family buildings and schools trade pneumatic or basic thermostats for real DDC, with a built-in browser interface and no head-end server required.

Are Vector Controls controllers BTL certified?

Yes. Vector X2 controllers are BTL certified and listed under certificates 30869 (BACnet MS/TP) and 30963 (BACnet/IP), which you can verify on the BACnet International registry. BTL listing confirms the controllers have been independently tested for BACnet interoperability with other certified devices.

Get in touch

Let's put open-protocol control on your next spec.

Whether it's a single retrofit or a basis-of-design listing for your firm's templates, we'll get you the datasheet, I/O list, or sample sequence you need.

Send Project Info →
Premier Energy Controls
ContactKevin
RoleU.S. Dealer Representative/Support
LocationTwin Cities, MN
ManufacturerVector Controls LLC, Bethel, CT